AutoTrac reduces overlap

 

AutoTrac maintains speed

Farming requires multiple passes. This requires a method of guidance with a high degree of repeatability in order to minimize overlap (extra cost of seed, fertilizer, chemical and machine hours) and skips (loss of production).

Maintaining repeatable accuracy is important in all operations, especially with cropping practices that require multiple passes through the field. AutoTrac creates more consistent row spacing, reducing the potential for crop damage with subsequent passes through the field.

University studies have shown that operators tend to overlap 5 to 13 percent over the course of an entire day, which could mean up to 60 cm (23 in.) of overlap with a 6 m (19 ft) tillage implement. This means that a producer with 300 ha (740 acres) actually works and pays for 330 ha (815 acres).

With reducing overlap by using AutoTrac more ground is covered in the same time and inputs like chemicals, fertilizer, fuel, labor and machine hours are reduced.

Reduce compaction with AutoTrac™ guidance system

As tractors and field equipment become larger and heavier, there is a growing concern about soil compaction. Heavy equipment and tillage implements can cause damage to the soil structure. Soil structure is important because it determines the ability of a soil to hold and conduct water, nutrients, and air necessary for plant root activity.

By using AutoTrac, operators can optimize the number of passes and reduce compaction. Additionally, the operator can confine traffic between certain rows and avoid compacting the row area.

AutoTrac allows producers to use the same traffic lanes year after year, sacrificing a small portion of the field in favor of having no wheel traffic in the majority of the field. Restricting traffic to specific lanes also provides a firm soil surface for more efficient tractor operation.

Without using AutoTrac during field operations, there is tendency for passes to overlap. Each pass over a field under poor conditions can cause significant damage to the soil.

AutoTrac™ guidance steering system allows operators to use tramline management more effectively, minimizing soil compaction. Additionally, AutoTrac allows the machine operator to select from a variety of guidance modes including straight track, AB curves, adaptive curves, circle track, boundary fill, machine access, and swap track. These tracking options allow the operator to select the track best suited for the field and conditions reducing the number of passes needed to cover the field.

CURVE TRACK

Curve track

The curve track mode helps operators by automatically steering curved guidance lines on terrain that does not allow for straight track to be used (rolling hills or contours).
 
When running with curve track, keep in mind these basic principles:

• Straight track is more accurate than curve track.
• A machine with an integrated AutoTrac steering kit is more accurate than a machine with the AutoTrac Universal steering kit.
• Slower speeds are more accurate than faster speeds.
• Gentle curves are more accurate than tight turn radius curves.

TYPES OF CURVES

Two different modes can be used depending on the type of curves that need to be created: adaptive curves or A/B curves.

Adaptive curve track

This track allows the operator to record a manually driven curved guidance line. Operators using a GreenStar™ 3 2630 Display have the ability to record and utilize multiple adaptive curves per field. This feature is especially useful as operators maneuver around terraces or irregular, constantly changing fields. Adaptive curve mode also has the ability to connect line segments when documentation is selected as the recording source. Self-propelled forage harvester or combine operators may find this functionality useful if they need to quickly raise their header for any reason.

The curve adapts, if driven around an obstacle

 

The curvature of the line changes down the field

A/B curve track 

This track allows the operator to set a curved line in a field with two end points (A and B) and will generate guidance lines parallel to the initial track in either direction.

Skip pass

 

The line stays the same across the field, and an operator can use skip track.

Field obstacles

 

Even if an operator drives around an obstacle in the field, the next pass follows the original track line.

STRAIGHT TRACK

Subsequent passes are identical to the first pass

 

The straight track mode helps operators by automatically driving straight. Operators can create an initial straight line using a variety of different setup options.

Once the track has been defined, all subsequent track lines in the field are created parallel to each other at the defined track spacing distance.

MANUAL CIRCLES WITH PARALLEL TRACKING GUIDANCE SYSTEMT

Circle track mode on the display

 

The circle track mode helps operators drive concentric circles in a field when a circle is set up and guidance is being used. Operators can create an initial circle using a variety of different methods. Once the initial circle has been defined, all the subsequent circles in the field are created.

Circle track is available in Parallel Tracking mode. Pivot Pro activation must be purchased to use circle track with automatic guidance.

CONCENTRIC CIRCLES WITH PIVOT PRO

Pivot Pro tracking mode

 

The Pivot Pro module allows the operator to automatically guide a machine in defined concentric circles in fields with center-pivot irrigation systems.

Circle track functionality is included with GreenStar Basics, allowing the operator to manually guide the machine around the concentric circle without an upgrade activation. Pair Pivot Pro activation with GreenStar AutoTrac to have the machine drive circles automatically.

Pivot Pro is approved for level fields, as accuracy can be degraded as slope increases. If there is slope in the field, there is the potential the circle track space and the center-pivot tower track will not match up. Keep in mind, AutoTrac draws the circle spacing as if the plane were level.

FOLLOW TRACK MODE REDUCES COMPACTION

Active Implement Guidance™ uses the follow track mode

 

Unique to John Deere Active Implement Guidance, the follow track mode assists the driver when operating headlands or navigating around obstacles, allowing the implement to follow the tractor guidance path. This helps reduce crop damage and soil compaction.

TRAMLINE MANAGEMENT

Tramline screen

 

Tramline management provides the opportunity to setup and edit certain guidance lines as tramlines. Those lines will be highlighted in a separate color in the guidance screen. Tramline management is available on the GreenStar 3 2630 Display in straight track, AB curve, and circle track modes.

Tramlines can be set and stored for each A-B line in the display. This allows the operator to properly seed and plant fields with accurate tramlines defined. This will make it easier to reduce inputs on all following field operations such as spraying.

NOTE: Tramline management is not currently available on the GreenStar 3 CommandCenter™ controls.

Swap track
 
Swap track provides operators the ability to quickly switch guidance modes as they work through fields varying geographic conditions. Operators can easily move from straight track to any of the other tracking modes as needed. Swap track allows the operator to toggle between up to four different guidance lines within the same field on the GreenStar 3 2630 Display. Operators can also change the track order while AutoTrac is engaged.
 
Swap track is available on the GreenStar 3 2630 Display.
 
NOTE: Swap track is not available on the GreenStar 3 CommandCenter.

AutoTrac™ steering kits on new tractors

 

AutoTrac Universal for older and non-John Deere machines

When paired with a StarFire™ Receiver and GreenStar™ Display, the machine steering kit completes the components that automatically steer the machine. Regardless of the steering kit, the receiver and display help standardize the operating experience between various machines in the operation. This reduces the learning curve for new operators and makes it easier for the operator to focus on total machine optimization.

Three different options are available:

• Integrated steering kit
• AutoTrac Universal steering kit
• AutoTrac Controller steering kit

AutoTrac – Integrated steering kit

The integrated steering kit is tied directly into the steering system on the machine and therefore provides optimum accuracy.

• Integrated – for a clean look in the machine
• Recent John Deere machines
• Team John Deere precision with John Deere machines for the highest level of performance, acquisition and accuracy

AutoTrac Universal

A universal system does not integrate into the existing steering system and can be moved between machines.

• Universal system can easily be moved between machines
• John Deere and non-John Deere machines
• Good acquisition and line accuracy

AutoTrac Controller

AutoTrac Controller is a field-installed, integrated AutoTrac system that is available on older John Deere and non-John Deere tractors.

• Integrated
• Older John Deere and non-John Deere tractors
• Enjoy an uncluttered cab
• Increased performance over a universal system

INTEGRATED AUTOTRAC KITS ARE AVAILABLE FACTORY INSTALLED ON THE FOLLOWING JOHN DEERE MACHINES:

• 6R Series Tractors with mechanical front-wheel drive (MFWD)
• 7R Series Small-frame Tractors with MFWD
  • In base, no deduct option
• 7R Series Large-frame Tractors with MFWD
  • In base, no deduct option
• 8R Series Tractors with MFWD or tracks
  • In base, no deduct option
• 9R Ag and Scraper Series Tractors with tracks or wheel
• 4630 / 4730 / 4830 / 4 Series Sprayers
  • In base, no deduct option
• S-Series and T-Series Combine
  • In base, no deduct option
• 7080 Series Self-Propelled Forage Harvester
• W200 Series Self-Propelled Windrower
  • In base, no deduct option
• 7760 / 7660 Cotton Pickers
  • In base, no deduct option
• 3520T Sugarcane Harvesters
  • In base, no deduct

INTEGRATED KITS ARE AVAILABLE FOR FIELD INSTALLATION ON THE FOLLOWING JOHN DEERE MACHINES:

• 6420 / 6030 / 6R Premium Series Tractors with MFWD
• Small-frame 7020 / 7030 Premium Series Tractors with MFWD
• Large-frame 7020 / 7030 Series Tractors with MFWD
• 8000 / 8010 / 8020 Series Tractors with MFWD or tracks
• 9000 / 9020 Series Tractors with tracks or wheel
• 9030 Wheeled Special Series Tractors (Not compatible with 9030 Track Special Series Tractors)
• 9R / 9RT Scraper Series Tractors
• 4700 / 4710 / 4720 / 4920 / 4730 / 4830 Series Sprayers
• 9050 / 9060 / 9070 Series Combines
• 7000 / 7050 / 7080 Series Self-Propelled Forage Harvesters